Samsung S8500 Wave
- ?
- Anonymous
- Y}5
- 12 Oct 2010
does dis fone hav free navigation ...... Plz tell me or i shud go for nokia n8
- ?
- Anonymous
- 3@j
- 12 Oct 2010
Saurav, 12 Oct 2010When the 1.2 bada will be available in Kies? Eagerly waitin... morebada 1.2 will be available through kies in the end of november.If you do not have patience to wait, put bada 1.2 with multiloader
- S
- Saurav
- 2SU
- 12 Oct 2010
When the 1.2 bada will be available in Kies? Eagerly waiting for it....Does anyone know???
- ?
- Anonymous
- 3@j
- 12 Oct 2010
JT, 12 Oct 2010Hey I just wanto tune up the voice recorder as good as camc... morepeople again, please do not ask again and again same questions.Answer on every your question are on the earlier pages, but i will repeat again
If you have low sound in speaker ,microphone... You should change values in administration mode.
Type *#197328640#
Click the button 5 ( Audio )
Click the button 2 ( AP, Volume Config)
Click on the button 2 (EAR Config )
Click the button 1 (volume MP) - to increase the volume of music files or the 5 key (FM Radio volume ) - Radio
We can see the 7 lines (0-6 ) we can increase the value of
all lines (these are the lines that define the level at each
support ), you can change any of them or increase only
last value of 58dB to 75dB and 100db max .
To increase headphone volume, select line 6 and then tap on the white box below the number keypad several times. A new window will pop up - Enter the value over there. Click on done and ok twice.
- J
- JT
- nXf
- 12 Oct 2010
Jatin, 12 Oct 2010In Reply to anonymous.. Hey follow this same procedure f... moreHey I just wanto tune up the voice recorder as good as camcorder sensitivity dolby range.Because up and till now is really weak.I hv to put it like a mic towards the mouth inorder to hv a clear voicememo.Nokia voice memo was way better then this.So if u Wizard of wave know how Come with a protocol..Immediately and effectively.Please giude T.Y. ;)
- ?
- Anonymous
- t4n
- 12 Oct 2010
new usb icon on bada 1.2 so there might b usb on the go feature for bada 1.2..
- ?
- Anonymous
- j01
- 12 Oct 2010
swype on bada 1.2 is amazing!!!!!!!!!!!!
This is the most beautiful phone ever made.Built quality is piece of art!!!!!!!!
The class of memory card is written on the card
http://tech.smartcanucks.ca/kingston-8gb-sdhc-class-6-amazon/
- ?
- Anonymous
- v0X
- 12 Oct 2010
Anonymous, 12 Oct 2010If you want to instal something to memory card, watch hd mo... morehow will you know about the class.. pls cuz i dont understand it..
- ?
- Anonymous
- t4n
- 12 Oct 2010
bada 2.0 whats new features they r addin??
- S
- Shanu
- 2Tb
- 12 Oct 2010
dose this phone has slide out qwerty keyboard.
- ?
- Anonymous
- j01
- 12 Oct 2010
samsung currently works on bada 2.0 which eat i phone operating system and android alive
- a
- anup nigam
- tUX
- 12 Oct 2010
does samsung wave has (UE)3G compatibility equipment
- ?
- Anonymous
- t4n
- 12 Oct 2010
10)new games instaled?
- n
- nicky
- f4R
- 12 Oct 2010
I have used the Sony Ericsson P910i, Nokia N95 8G and the Samsung Omnia i900 8G over the last few years. I was very happy with all of them. My next phone was to come from a long list of possiblilties. The Wave was not on the list. A friend of mine said that before I make a decision, I should look at the Wave as well. I bought it. What a piece of art, lovely, easy to work, vivid screen, smooth, fast, good built quality,....
- P
- PRASHANT
- mIf
- 12 Oct 2010
Anonymous, 12 Oct 2010For all people who can not update their phones.This is the ... moreso my frnd u hv upgraded ur phone or not? did u see any change? this is important, did u find swype input method for message. i m waiting for ur reply than i will go for upgrade.....last time i faced i lot of problem...and i did not see any change.....i m indian user...thank u
- ?
- Anonymous
- 3@j
- 12 Oct 2010
If you want to instal something to memory card, watch hd movies from memory card... buy class 6 !!!!!!!!!!! with class 6 you will not have lag at all.
- h
- hohoho
- PVv
- 12 Oct 2010
guys, do u know if we can backup apps in our phone? coz i hv some free apps that become paid recently and i want to flash to bada 1.2 without losing the apps.any idea?
- ?
- Anonymous
- 3@j
- 12 Oct 2010
Jatin, 12 Oct 2010Hey Guyz...
How many times shud i post my problem on this ... moreFor all people who can not update their phones.This is the solution.It is completely safe and very easy.Ater you doing this you will be uble to update phone throw kies.
First of all you have download bada 1.2 with and multiloader from http://www.multiupload.com/8P155MOV1J
the battery life will take a small hit when upgraded to bada 1.2
plz backup all your contacts,messages,videos,photos by using kies and also make a note of the apps that u installed or else u will lose ur data.
also it is good if u make a note of the bluetooth and wifi mac id:- with the imei no.
1.Unzip the downloaded .rar file(password is:-samfirmware.com)
2.open extracted folder
3.open Multiloader (Run as administrator if you are using Vista or windows 7)
4.select LSI
5.Check Full Download (Do not check Boot Change cause it may gives some serious problem if you didn't flash properly)
6.Click Amss button and select amss.bin file from extracted folder..
7.like this select all files
8.Apps - apps_compressed.bin
9.Rsrc1 - Rsrc_S8500_Open_Europe_Common.rc1
10.Rsrc2 - Rsrc2_S8500_Open_Euro_Common(Low).rc2
11.Factory FS - FactoryFs_S8500_Open_Europe_Common.ffs
12.CSC - CSC_S8500_Open_Europe_Common_OXA_XXJID.csc
13.SHP APP - ShpApp.app
14.Power off your phone(Wave)
15.connect your phone to pc using Usb cable provided with Wave..(Make sure that samsung kies installed on your pc).
16.Press and hold the following keys to enable Download mode
(Down Volume key, Lock button, End key(Power on or off button))
17.Now the phone will turned on with Download Enabled mode.
18.On the pc the driver will installed if it is not already installed.Wait until it finishes the installation process of Driver
19.Now press "Port Search" button on the Multiloader window
20.then it will show the Ready status if the driver installed properly(means the phone is connected properly)
21.Now press Download Button. It will start the flashing procedure. wait for 5 to 20 minutes( Approx)
After completing the flashing process the phone will restarts automatically.and then u will get a blue screen with some codes and again the phone will restart automatically.
22.Disconnect the Usb cable.
23.after u successfully install the new firmware hard reset by using *2767*3855# and then the phone will boot.
24.use this tutorial to update the camera firmware-
http://www.samfirmware.com/app...era-fw-s8500
25.then change to cp UART (full power) or ap uart (powersaver) modes via *#8740# as u like
26.lastly check if bluetooth,wifi or imei id's are changed or not.
27.download the latest route 66 maps.
note- If it gets stuck on the bada screen when it restarts take out battery and then it will restart and work properly.
then if u like to increase the volume of wave then go to-
AP Volume Config by *#197328640# - Internal Settings
- SPK Config / Voice Call Volume
4: 57 -> 77 et 5: 57 -> 87 et 6: 57 -> 97
- SPK Config / MP Volume
5: 61-> 67 et 6: 61 -> 77
- SPK Config / Voice Memo Volume
0/1/2/3/4/5/6: 58 -> 100
- SPK Config / REC Volume
0/1/2/3/4/5/6: 63 -> 100
- SPK Config / Ringtone Volume
5: 61 -> 77 et 6: 61 -> 87
Steps to install Product Code of ur choice-
My original product code was Product Code: GT-S8500BAAFOP.
When I installed the S8500XXJID_Flash Full, and choose XEU in preconfiguration setting,
my product code was changed to GT-S8500BAAXEU in registry.
I tried to revert back to my original GT-S8500BAAFOP by installing all available
full firmwares, starting with S8500XXJF1 to S8500XXJH3 (using OXC CSC) but the registry
still showed my product code as GT-S8500BAAXEU.
At last I found the solution. And with this method, you can freely now choose the product code you
want for your phone. Just follow the steps below:
1. Install S8500XXJID_Full with the CSC file that contains the product code of your choice
(Example 1: OXA for SKT, XEO, XEF. XEU, ITV, DBT (Germany, France,UK, Italy, etc
2: OXC for FOP, THP, EUR (Spain, Portugal, Greece, etc)
3. etc, etc.
2. After installation, hard reset phone. Then go to admin mode => preconfiguration => and
install the CSC of your choice. Whichever you install will now be your product code.
Connect phone to KIES and check your windows registry.
NOTE: If you install S8500XXJID_Full with the default CSC file (in example 1 above) it's all easy.
But if you install with any other CSC file, phone will normally reboot constantly if you try to go
into MENU and setting. Don't worry, just install, hard reset, then enter admin mode to install your preferred CSC.
Once done, your product code will now be that of the CSC you have installed.
You can now put off phone, and flash your phone with that country's firmware and update to latest firmware via KIES.
OBSERVATION: I have tried this experiment with 2 XX phones and it worked perfectly for me.
Others should try and give feedback.
ADVANTAGES: If you have, for example, product code GT-S8500BAAFOP (Spain) with latest firmware as JH1.
And in Germany, for example, KIES has newer firmware, say JH7.
You can easily change your product code to GT-S8500BAADBT and upgrade via KIES.
Here are Some of the Codes which u can use to check ur phone info..
*#1234# - Shows Firmware version.
*#197328640# - Internal Settings
*2767*3855# - Hard Reset
*#0228# - Battery Info
*#0*# - LCD test
cp UART (full power) or ap uart (powersaver) modes via *#8740#
preconfiguration:
Administration mode: *#5239870*#
Preconfiguration: *#27236*#